ASTM B622 / ASME SB622 / Seamless Nickel and Nickel Cobalt Alloy Pipe and Tube supplier & distributor in India

ASTM B-622 , ASME SB-622

SPECIFICATION FOR SEAMLESS NICKEL AND NICKEL COBALT ALLOY PIPE AND
TUBEHASTELLOY B-2 = UNS N10665 , HASTELLOY C-270 =UNS N10276

1.Scope

1.1 This soecification covers seamless pipe and tube of nickel and nickel-cobalt lloys (UNS N10001, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N08315, UNS N06255, UNS N06059, UNS N06530, UNS N08031, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06320, UNS N06686, UNS N10629, and UNS R20033) as shown in Table

1. 1.2 Pipe and ube shall be supplied in the solution annlealed and descaled condition. When atmosphere contro; is used, descaling is not necessary.

1.3 The values state in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

TABLE1 CHEMICAL REQUIREMENTS

	Composition Limits, %
	Ni	Cr	Mo	Fe	W	C	Si max	Co	Mn	V
Ni-Mo Alloys N10001	Remainder [Note(1)]	1.0max	26.0-30.0	4.0-6.0	...	0.05max	1.0	2.5max	1.0max	0.2-0.4
N10665	Remainder [Note(1)]	1.0max	26.0-30.0	2.0max	...	0.02max	0.10	1.0max	1.0max	...
N10675	65.0min	1.0-3.0	27.0-32.0	1.0-3.0	3.0max	0.01max	0.10	3.0max	3.0max	0.20max
N10629	Remainder [Note(1)]	0.5-1.5	26.0-30.0	1.0-6.0	...	0.01max	0.05	2.5max	1.5max	...
Low C Ni-Mo-Cr Allys N10276	Remainder [Note(1)]	14.5-16.5	15.0-17.0	4.0-7.0	3.0-4.5	0.010max	0.08	2.5max	1.0max	0.35max
N06022	Remainder [Note(1)]	20.0-22.5	12.5-14.5	2.0-6.0	2.5-3.5	0.015max	0.08	2.5max	0.50max	0.35max
N06455	Remainder [Note(1)]	41.0-18.0	14.0-17.0	3.0max	...	0.015max	0.01	2.0max	1.0max	...
Ni-Cr-Fe-Mo-Cu Alloys N06007	Remainder [Note(1)]	21.0-23.5	5.5-7.5	18.0-21.0	1.0max	0.05max	1.0	2.5max	1.0-2.0	...
N06975	47.0-52.0	23.0-26.0	5.0-7.0	Remainder [Note(1)]	...	0.03max	1.0	...	1.0max	...
N06985	Remainder [Note(1)]	21.0-23.0	6.0-8.0	18.0-21.0	1.5max	0.015max	1.0	5.0max	1.0max	...
N06030	Remainder [Note(1)]	28.0-31.5	4.0-6.0	13.0-17.0	1.5-4.0	0.03max	0.8	5.0max	1.5max	...
N06255	47.0-52.0	23.0-26.0	6.0-9.0	Remainder [Note(1)]	3.0max	0.03max	1.0	...	1.0max	...
N06250	50.0-54.0	20.0-23.0	10.1-12.0	Remainder [Note(1)]	0.25-1.25	0.020max	0.09	...	1.00max	....
Ni-Fe-Cr-Mo Alloy N08320	25.0-27.0	21.0-23.0	4.0-6.0	Remainder [Note(1)]	...	0.05max	1.0	...	2.5max	....
N08135	33.0-38.0	20.5-23.5	4.0-5.0	Remainder [Note(1)]	0.20-0.80	0.030max	0.75	...	1.00max	....
Ni-Cr-Mo-Fe Alloy N06002	Remainder [Note(1)]	20.5-23.5	8.0-10.0	17.0-20.0	0.20-1.0	0.05-0.15	1.0	0.5-2.5	1.0max	...
N06060	5.4-60.0	19.0-22.0	12.0-14.0	Remainder [Note(1)]	0.25-1.25	0.03max	0.50	...	1.50max	...
Ni-Fe-Cr-Mo Alloy R30556	19.0-22.5	21.0-23.0	2.5-4.0	Remainder [Note(1)]	2.0-3.5	0.05-0.15	0.20-0.80	16.0-21.0	0.50-2.00	...
Ni-Cr-W-Mo Alloy N06230	Remainder [Note(1)]	20.0-24.0	1.0-3.0	3.0max	13.0-15.0	0.05-0.15	0.25-0.75	5.0max	0.30-1.00	...
Ni-Cr-W-Mo-Cu Alloy N06059	Balance	22.0-24.0	15.0-16.5	1.5max	...	0.010max	0.10	0.3max	0.5max	...
Ni-Fe-Cr-Mo-low Carbon Alloys N08031	30.0-32.0	26.0-28.0	6.0-7.0	Balance	...	0.015max	0.3	...	2.0max	...
N08535	29.0-36.5	24.0-27.0	2.5-4.0	Remainder [Note(1)]	...	0.03max	0.50	...	1.0max	...
Low C-Ni-Cr-Mo-W Alloy N06686	Remainde r[Note(1)]	19.0-23.0	15.0-17.0	5.0max	3.0-4.4	0.010max	0.08	...	0.75max	...
Ni-Co-Cr-Si Alloy N12160	Remainder [Note(1)]	26.0-30.0	1.0max	3.5max	1.0max	0.15max	2.4-3.0	27.0-33.0	1.5max	...
Cr-Ni-Fe-N Alloy R20033	30.033.0	31.0-35.0	0.50-2.0	Balance	...	0.15max	0.50	...	2.0max	...

	Composition Limits, %
	P max	S max	Ti	Cu	Cb(Nb)+Ta	Al	Zr	La	N	B	Cb(Nb)	Ta	Ni+Mo	Mg
Ni-Mo Alloys N10001	0.04	0.03	...	...	...
N10665	0.04	0.03	...	...	...
N10675	0.030	0.010	0.20max	0.20max	...	0.50max	0.10max	...	...	...	0.20max	0.20max	94.0-98.0
N10629	0.04	0.01	...	0.5max	...	0.1-0.5	...	...	...	...	...	...	...
Low C Ni-Mo-Cr Allys N10276	0.04	0.03	...	...	...
N06022	0.02	0.02	...	...	...
N06455	0.04	0.03	0.70max	...	...
Ni-Cr-Fe-Mo-Cu Alloys N06007	0.04	0.03	...	1.5-2.5	1.75-2.5
N06975	0.03	0.03	0.70-1.50	0.70-1.20	...
N06985	0.04	0.03	...	1.5-2.5	0.50max
N06030	0.04	0.02	...	1.0-2.4	0.30-1.50
N06255	0.03	0.03	0.36max	1.2max	...
N06250	0.030	0.005	...	0.25-1.25	...
Ni-Fe-Cr-Mo Alloy N08320	0.04	0.03	4×C min	...	...
N08135	0.03	0.03	...	0.70max	...
Ni-Cr-Mo-Fe Alloy N06002	0.04	0.03	...	...	...
N06060	0.030max	0.005max	...	0.25-1.25	0.50-1.25
Ni-Fe-Cr-Mo Alloy R30556	0.04	0.015	...	...	...	0.10-0.50	0.001-0.10	0.005-0.10	0.10-0.30	0.02 max	0.30max	0.3-1.25
Ni-Cr-W-Mo Alloy N06230	0.03	0.015	...	...	...	0.20-0.50	...	0.0005-0.050	...	0.015 max	...
Ni-Cr-W-Mo-Cu Alloy N06059	0.015	0.005	...	...	...	0.1-0.4	...	...	...	...	...	...
Ni-Fe-Cr-Mo-low Carbon Alloys N08031	0.020	0.010	...	1.0-1.4	...	...	...	...	0.15-0.25	...	...	...
N08535	0.03	0.03	...	1.50max	...
Low C-Ni-Cr-Mo-W Alloy N06686	0.04	0.02	0.02-0.25	...	...	...	...	...	...	...	...	...
Ni-Co-Cr-Si Alloy N12160	0.030	0.015	0.20-0.80	...	...	...	...	...	...	...	1.0max	...	...	...
Cr-Ni-Fe-N Alloy R20033	0.02	0.01	...	0.3-1.20	...	...	...	...	0.35-0.60	...	...	...	...	...

NOTE :(1)See 1.3.1.1 Mechanical Properties

Alloy

psi

MPa

Nickel-Molybdenum :

UNS N10001

25,000

172

UNS N10665

27,500

190

UNS N10675

27,500

190

UNS N10629

27,500

190

Low Carbon Nickel-Molybdenum-

Chromium :

UNS N10276

25,000

172

UNS N06022

25,000

172

UNS N06455

25,000

172

Nickel-Chromium-Iron-

Molybdenum-Copper:

UNS N06007

22,500

152

UNS N06975

21,000

145

UNS N06985

22,500

155

UNS N06030

21,000

145

UNS N06255

21,000

145

UNS N06250

22,500

155

Nickel-Iron-Chromium-

Molybdenum:

UNS N08320

18,500

127

UNS N08135

18,300

126

Nickel-Chromium-Molybdenum-

Iron:

UNS N06002

23,000

159

UNS N06060

22,500

155

Nickel-Iron-Chromium-Cobalt:

UNS R30556

25,000

172

Nickel-Chromium-Tungsten-

Molybdenum:

UNS N06230

27,500

190

Low Carbon-Nickel-Iron-Chromium-Mo-

lybdenum:

UNS N06059

25,000

172

Low Carbon Nickel-Iron-Chromium-

Molybdenum-Copper:

UNS N08031

22,500

155

UNS N08035

18,300

126

Low Carbon-Nickel-Chromium Mo-

lybdenum-Tungsten:

UNS N06686

25,000

172

Nickel-Cobalt-Chromium-Silicon:

UNS N12160

22,500

155

Chromium-Nickel-Iron-Nitrogen:

UNS R20033

22,700

186

TABLE2 PRDUCT9CHECK) ANALYSIS TOLERANCES

Element	Specified Limit or Max of Element, %	Variation Under Min. or Over Max., of the Specified Limit of Element, %
Nickel	Over 10.00 to 20.00, incl	0.20
	Over 20.00 to 30.00, incl	0.25
	Over 30.00 to 40.00, incl	0.30
	Over 40.00 to 60.00, incl	0.35
	Over 60.00 to 80.00, incl	0.45
Chromium	Up to 1.00	0.05
	Over 1.0 to 5.00	0.10
	Up to 5.00, incl	0.10
	Over 5.00 to 15.00, incl	0.15
	Over 15.00 to 25.00, incl	0.25
	Over 25.00 to 35.00, incl	0.35
Molybdenum	Up to 1.00, incl	0.03
	Over 1.00 to 3.00, incl	0.05
	Over 3.00 to 5.00, incl	0.10
	Over 5.00 to 20.00, incl	0.15
	Over 20.00 to 30.00, incl	0.25
	Over 30.00 to 40.00, incl	0.35
Iron	Over 0.75 to 2.50, incl	0.05
	Over 2.50 to 5.00, incl	0.07
	Over 5.00 to 10.00, incl	0.10
	Over 15.00 to 30.00, incl	0.30
Tungsten	Up to 1.00, incl	0.04
	Over 1.00 to 3.00, incl	0.10
	Over 3.00 to 5.00, incl	0.15
	Over 10.00 to 20.00, incl	0.25
Carbon	Up to 0.03, incl	0.005
	Over 0.03 to 0.20, incl	0.01
Silicon	Up to 0.05	0.01
	Over 0.05 to 0.25, incl	0.02
	Over 0.50 to 1.00, incl	0.05
	Over 1.00 to 4.50, incl	0.10
Cobalt	Over 0.20 to 1.00, incl	0.03
	Over 1.00 to 5.00, incl	0.05
	Over 15.00 to 20.00, incl	0.20
	Over 20.00 to 25.00, incl	0.25
	Over 25.00 to 30.00, incl	0.30
	Over 30.00 to 35.00, incl	0.35
Manganese	Up to 1.00, incl	0.03
	Over 1.00 to 3.00, incl	0.04
Vanadium	Up to 0.50, incl	0.04
Phosphorus	All	0.005
Sulfur	Up to 0.02, incl	0.003
	Over 0.02 to 0.060, incl	0.005
Titanium	Up to 0.10, incl	0.02
	Over 0.10 to 0.50, incl	0.03
	Over 0.50 to 1.00, incl	0.04
	Over 1.00 to 2.00, incl	0.05
Copper	Up to 0.20, incl	0.02
	Over 0.20 to 0.50, incl	0.03
	Over 0.50 to 5.00, incl	0.04
Columbium(Nb)+Tantalum	Up to 1.50, incl	0.05
	Over 1.50 to 3.00, incl	0.10
Aluminum	Up to 0.10, incl	0.02
	Over 0.10 to 0.50, incl	0.05
Boron	Over 0.01 to 0.005	0.005
Zirconium	Up to 0.10, incl	0.01
Nitrogen	Up to 0.02, incl	0.05
	Over 0.02 to 0.19, incl	0.01
	Over 0.19 to 0.25, incl	0.02
	Over 0.25 to 0.35, incl	0.03
	Over 0.35 to 0.45, incl	0.04
	Over 0.45 to 0.60, incl	0.05

TALBLE3 MECHANICAL PROPERTIES OF PIPE AND TUBE

Alloy	Tensile Strength, Min., ksi(MPa)	Yield Strength(0.2% Offset)Min., ksi(MPa)	elongation in 2 in.(50.8mm) or 4D,[Note(1)]Min., %
Ni-Mo
UNS N10001	100(690)	45(310)	40
UNS N10665	110(760)	51(350)	40
UNS N10675	110(760)	51(350)	40
UNS N10629	110(760)	51(350)	40
Low C-Ni-Mo-Cr
UNS N10276	100(690)	41(283)	40
UNS N06022	100(690)	45(310)	45
UNS N06455	100(690)	40(276)	40
Ni-Cr-Fe-Mo-Cu
UNS N06007	90(621)	35(241)	35
UNS N06975	85(586)	32(221)	40
UNS N06985	90(621)	35(241)	40
UNS N06030	85(586)	35(241)	30
UNS N06255	85(586)	32(221)	40
UNS N06250	90(621)	35(241)	40
Ni-Fe-Cr-Mo
UNS N08320	75(517)	28(193)	35
UNS N08135	73(503)	31(214)	40
Ni-Cr-Mo-Fe
UNS N06002	100(690)	40(276)	35
UNS N06060	90(621)	35(241)	40
Ni-Fe-Cr-Co-R30556	100(690)	45(310)	40
Ni-Cr-W-Mo
UNS N06230	110(760)	45(310)	40
Low C-Ni-Cr-Mo
UNS N06059	100(690)	45(310)	45
Ni-Fe-Cr-Mo-Cu Low Carbon
UNS N08031	94(650)	40(276)	40
UNS N8535	73(503)	31(214)	40
Low C Ni-Cr-Mo-W
UNS N06686	100(690)	45(310)	45
Ni-Co-Cr-Si
UNS N12160	90(620)	35(240)	40
Cr-Ni-Fe-N
Low Carbon	109(750)	55(380)	40

NOTE: (1) D refers to the diameter of the tension specimen.

TABLE4 PERMISSIBLE VARIATIONS IN OUTSIDE DIAMETER AND WALL THICKNESS(AVERAGE WALL)

Specified Outside diameter	Wall Thickness, %
	Outside Diameter		Average		Minimum Wall
	+	-	+	-	+	-
Inches
0.500 to 5/8, incl	0.005	0.005	12.5	12.5	25.0	0
Over 5/8 to 1 1/2, incl	0.0075	0.0075	10.0	10.0	20.0	0
Over 1 1/2 to 3 1/2, incl	0.010	0.010	10.0	10.0	22.0	0
Milimeter
12.7 to 15.88, incl	0.13	0.13	12.5	12.5	25.0	0
Over 15.88 to 38.100, incl	0.190	0.190	10.0	10.0	20.0	0
Over 38.100 to 88.900, incl	0.254	0.254	10.0	10.0	22.0	0

	S
Alloy	lb/in.3	g/cm3
Nickel-Molybdenum :
UNS N10001	0.334	9.24
UNS N10665	0.333	9.22
UNS N10675	0.333	9.22
UNS N10629	0.333	9.22
Low Carbon Nickel-Molybdenum- Chromium :
UNS N10276	0.321	8.87
UNS N06022	0.314	8.69
UNS N06455	0.312	8.64
Nickel-Chromium-Iron- Molybdenum-Copper:
UNS N06007	0.3	8.31
UNS N06975	0.295	8.17
UNS N06985	0.3	8.31
UNS N06030	0.297	8.22
UNS N06255	0.299	8.29
UNS N06250	0.307	8.58
Nickel-Iron-Chromium- Molybdenum:
UNS N08320	0.291	8.05
UNS N08135	0.292	8.1
Nickel-Chromium-Molybdenum- Iron:
UNS N06002	0.297	8.23
UNS N06060	0.315	8.71
Nickel-Iron-Chromium-Cobalt:
UNS R30556	0.297	8.23
Nickel-Chromium-Tungsten- Molybdenum:
UNS N06230	0.319	8.83
Low Carbon-Nickel-Iron-Chromium-Mo- lybdenum:
UNS N06059	0.32	8.8
Low Carbon Nickel-Iron-Chromium- Molybdenum-Copper:
UNS N08031	0.29	8.1
UNS N08035	0.291	8.07
Low Carbon-Nickel-Chromium Mo- lybdenum-Tungsten:
UNS N06686	0.315	8.73
Nickel-Cobalt-Chromium-Silicon:
UNS N12160	0.292	8.08
Chromium-Nickel-Iron-Nitrogen:
UNS R20033	0.29	8.1

Product successfully added to your shopping cart

There are 64 items in your cart. There is 1 item in your cart.

Categories

Surplus stock of Steel Pipes & Tubes:

Specialist in:

Offering best price on:

Widest inventory of:

ASTM B622 / ASME SB622 / Seamless Nickel and Nickel Cobalt Alloy Pipe and Tube supplier & distributor in India

Steel pipe & tube ready inventory: