ASTM B165 / ASME SB165 / Nickel Copper Alloy (UNS N04400) Seamless Pipe and Tube supplier & distributor in India

ASTM B-165 , ASME SB-165

SPECIFICATION FOR NICKEL COPPER ALLOY(UNS NO4400)
SEAMLESS PIPE AND TUBE MONEL 400 = INCOLOY ALLOY 400

1.Scope

1.1 This specification covers nickel-copper alloy UNS N04400 in the form of cold-worked seamless pipe and tube in the condotions shown n Table 1.

1.2 The vales stated in inch-pound units are to be regared as the atandard. The values given in patenthses are for information only.

TABLE1 MECHANICAL PREPERTIES OF PIPE AND TUBE

Condition and Size	Tensile Strength, min, pas(MPa)	Yield Strength, min,(0.2% offset), min, psi(MPa)	elongation n 2in. or 50min(or4 D), min %
Annealed:
5in. (127mm) outside diameter and under	70000(480)	28000(195)	35
Over 5 in.(127mm) outside diameter Stress-Relieved	70000(480)	25000(170)	35
All sizes	85000(585)	55000(380)	15

TABLE2 CHEMICAL REQUIREMENTS

Element	Cmposition Limits, %	Product(Check) Analysis Variations, under min or over max, of the Specified Limit lf Element
NiA	63.0min	0.45
Cu	28.0min	0.15
	34.0max	0.20
Fe	2.5max	0.05
Mn	2.0max	0.04
C	0.3max	0.02
Si	0.5max	0.3
S	0.024max	0.005

AElement shall be determined arithmetically by difference.

TABLE3 PERMISSIBLE VARIATIONS FOR OUTSIE DIAMETER AND WALL
THICKNESS OF SEAMLESS COLD WORKED PIPE AND TUBEA,B

Permissible Variations
Nominal Outside Diameter, in.(mm)	Outside Diameter, in.(mm)		% of Thickness of Specified Nominal Wall		% of Thickness of Specified Minimum Wall
Nominal Outside Diameter, in.(mm)	+	-	+	-	+	-
Wver 0.400(10) to 5/8 (16), excl	0.005(0.13)	0.005(0.13)	15.0	15.0	30	0
5/8(16) to q 1/2 (38), incl	0.0075(0.19)	0.0075(0.19)	10.0	10.0	22	0
Over 1 1/2(38) to 3(76), incl	0.010(0.25)	0.010(0.25)	10.0	10.0	22	0
Over 3(76) to 4 1/2(114), incl	0.015(0.38)	0.015(0.38)	10.0	10.0	22	0
Over 4 1/2(114) to 6(152), incl	0.020(0.51)	0.020(0.51)	12.5	12.5	28	0
Over 6(152) to 6 5/8(168), incl	0.025(0.64)	0.025(0.64)	12.5	12.5	28	0
Over 6 5/8(168) to 8 5/8(219), incl	0.031(0.79)	0.031(0.79)	12.5	12.5	28	0

AOvality- The permissible variations in this table apply to individual measurements,
including out-of-roudness(ovality) except for the following:

For pipe and tube having a nominal wall thickness of 3% or less of the nominal otside diametter, the mean uotside diameter
shall conform to the permissible variations of this table and individual measruements(including ovality) shall conform to the
plus and minus values of the tale, with the values increased by 0.5% of the nominal outside diameter. fo peipe and tube
over4 1/2in.(114mm) in outside diameter with a nominal wall thickness greater than 3% of the nominal outside diameter, the
mean outside diameter shall conform to the permissible variations of this table and individual measurements shall not exceed
twice the permissible variations of the table.

BEccentricity- The permissible variations in tihis table apply to individual measurements including eccentricity.

TABLE4 PERMISSIBLE VARIATIONS IN LENGTHA

Outside Diameter, in.(mm)	Cut length, in. (mm)
Outside Diameter, in.(mm)	Over	Under
Under 2(50.8)	1/8(3.2)	0
2 (50.8) and over	3/16(4.8)	0

These permissible variations in length apply to pipe of tube in straight. They apply to cut lenghs up to and including 24ft(7.3m).
For lengths over 24ft, an additional over-tolerance of 1/8in. (3.2mm)for each 10ft(3.0m) or fraction thereofshall be permissible
up to a maximum additional over-tolllleance of 1/2in.(17.7mm)

TABLE X1.1 PIPE SCHEDULESA

Nominal Pipe Size in.	Outside Diameter in. (mm)	Nominal Wall Thickness, in. (mm)
Nominal Pipe Size in.	Outside Diameter in. (mm)	Schedule No. 5 in.(mm)	Schedule No. 10 in.(mm)	Schedule No. 40 in.(mm)	Schedule No. 80 in.(mm)
1/8	0.405(10.3)	...	0.049(1.2)	0.068(1.7)	0.095(2.4)
1/4	0.540(13.7)	...	0.065(1.6)	0.088(2.2)	0.119(3.0)
3/8	0.675(17.1)	...	0.065(1.6)	0.091(2.3)	0.126(3.2)
1/2	0.840(21.3)	0.056(1.6)	0.083(2.1)	0.109(2.8)	0.147(3.7)
3/4	1.050(26.7)	0.065(1.6)	0.083(2.1)	0.113(2.8)	0.154(3.9)
1	1.315(33.4)	0.065(1.6)	0.109(2.8)	0.133(3.4)	0.179(4.5)
1 1/4	1.660(42.2)	0.065(1.6)	0.109(2.8)	0.140(3.6)	0.191(4.8)
1 1/2	1.900(48.3)	0.065(1.6)	0.109(2.8)	0.145(3.7)	0.200(5.1)
2	2.375(60.3)	0.065(1.6)	0.109(2.8)	0.154(3.9)	0.218(5.5)
2 1/2	2.875(73.0)	0.083(2.1)	0.120(3.0)	0.203(5.2)	0.276(7.0)
3	3.500(88.9)	0.083(2.1)	0.120(3.0)	0.216(5.5)	0.300(7.6)
3 1/2	4.000(101.6)	0.083(2.1)	0.120(3.0)	0.226(5.7)	0.318(8.1)
4	4.500(114.3)	0.083(2.1)	0.120(3.0)	0.237(6.0)	0.337(8.6)
5	5.563(141.3)	0.109(2.8)	0.134(3.0)	0.258(6.5)	0.375(9.5)
6	6.625(168.3)	0.109(2.8)	0.134(3.0)	0.280(7.1)	0.432(10.9)
8	8.625(219.1)	...	...	0.322(8.2)	0.500(12.7)

A The pipe schedules shown above conform with standards adopted by the American National Standards Insitute.

Material Comparison Tables (ASTM →KS, JIS, DIN, BS, NBN, NF, UNI)

ASTMSTANDARD	UNS NO.	KOREA/JAPANES		GERMAN		BRITISH		ISO
ASTMSTANDARD	UNS NO.	KS/JIS Symbol	KS/JIS Numbe	DIN Type	DIN Number	B.S Number	B.S Grade	ISO Type	ISO Number
B 165 Nikel-Copper Alloy (UNSN04400) Seamless Pipe and Tube
N04400	N04400	/NCuT	/H4552	NW4400	17742	3074	NA12		9722

Product successfully added to your shopping cart

There are 64 items in your cart. There is 1 item in your cart.

Categories

Surplus stock of Steel Pipes & Tubes:

Specialist in:

Offering best price on:

Widest inventory of:

ASTM B165 / ASME SB165 / Nickel Copper Alloy (UNS N04400) Seamless Pipe and Tube supplier & distributor in India

Steel pipe & tube ready inventory: